Linear Motors & Alternators

More Views

Linear Motors & Alternators

Model # 1s102M

RIX’s linear motors & alternators are the driving force behind all our products. These are linear reciprocating devices that combine the unique flexing axial suspension with plunger-mounted, high-energy magnets and robust coil-over-iron stators. Each model is designed to operate for well over 10 maintenance-free years with a calculated mean time between failures per MIL-STD 217F of 129,760 hours. This is supported by 100’s of installations worldwide. These motors/alternators offer efficiencies in the 80%-90% range, much higher than similar linear reciprocating devices.
Description

Details

RIX’s linear motors & alternators are the driving force behind all our products. These are linear reciprocating devices that combine the unique flexing axial suspension with plunger-mounted, high-energy magnets and robust coil-over-iron stators. Each model is designed to operate for well over 10 maintenance-free years with a calculated mean time between failures per MIL-STD 217F of 129,760 hours. This is supported by 100’s of installations worldwide. These motors/alternators offer efficiencies in the 80%-90% range, much higher than similar linear reciprocating devices.

HOW IT WORKS:

Linear Reciprocating Motors, Alternators and Drivers

RIX’s acoustic drives are similar to a loudspeaker in your home stereo system.  A voltage signal is supplied and the speaker moves back and forth in response, pushing and pulling air in time with the frequency of the electrical signal.  The same principle applies here, though the device is a bit different.  The magnets move, not the coil, and they are supported by unlimited-life metallic flexures instead of paper or plastic.  Like a speaker, it needs no oil – an important advantage when using these devices in a cryocooler (cold oil is not useful!).  Unlike a speaker, it pushes not air, but typically high-pressure helium (one of two gases that remains a gas below 77K).  And because of that high pressure, the moving face area is smaller and stronger – a metal piston instead of a paper cone.  The metallic flexures are designed to hold such a straight line of motion that the pistons can be machined with just microns of clearance to their matched cylinders and run without contact or wearing. One other difference with speakers is that they are designed for an inefficient but ‘flat’ response across a wide range of pitch frequencies.  RIX’s are tuned to resonate at a single driving frequency (we use 50 or 60 Hz because it comes from the wall plugs!) to give high power and efficiency.

 Motor Mode:

  • Alternating voltage is applied to the linear motor.  Current flows through the motor windings, causing a magnetic field in the iron they surround.
  • The applied field, oscillating due to the reversing electrical input, pushes and pulls on permanent magnets mounted on the moving assembly, (called the piston-plunger).
  • When the applied voltage frequency is close to the resonant frequency of the motor and load combined, the piston oscillates and power is delivered to the acoustic load by phase separation of the current and piston displacement.
  • Typically, when connected to an acoustic load like a cryogenic coldhead, helium gas is cyclically compressed and expanded relative to the mean (charge) pressure by the piston of the driver to power a thermodynamic cycle for refrigeration.

Alternator Mode:

  • Alternating pressure is applied to the piston.  The force of the pressure (and associated gas flow) causes the piston to oscillate.  The frequency of oscillation is a system variable – applied pressure frequency must be close to the system resonance for optimal performance.
  • The oscillatory movement causes changing flux links between the magnets moving with the piston and the iron stator.
  • The reversing flux changes in the iron induce voltage in the windings.
  • If connected to a load resistance, the voltage causes current to flow and power to be delivered from the alternator.
  • Power factor (phase of voltage and current) can be corrected by use of an appropriate capacitor in series with the alternator and load.

 

 

Features

Features

The RIX Industries system provides no maintenance, linear reciprocating motors and alternators with oil-free flexure bearings that have virtually unlimited life. 

SYSTEM SPECIFICATIONS:

Motor Model 1s102M 1s132M 1s175M 1s226M 1s241M 1s297M 1s362M
               
Nominal Input Power Rating 120 W at 60 Hz, 10 mm stroke 275 W at 60 Hz, 12 mm stroke 750 W at 60 Hz, 16 mm stroke 1,400 W at 60 Hz, 20 mm stroke 2,000  W at 60 Hz, 20 mm stroke 5,000 W at 60 Hz, 26 mm stroke 10,000  W at 60 Hz, 32 mm stroke
Rated Acoustic Output (@ 60 Hz) Acoustic power as driver – 90 W Acoustic power as driver – 220 W  Acoustic power as driver – 550 W Acoustic power as driver – 1000 W Acoustic power as driver – 1,600W  Acoustic power as driver – 3800W Acoustic power as driver – 7500W
Stator Resistance 7 ohm 2.2 ohm 1.8 ohm 0.9 ohm 0.9 ohm @ 60Hz AC 0.2 ohm 0.22 ohm
Stator Inductance 84 mH @110 VAC RMS 46 mH @ 110 VAC RMS 62 mH  @ 208 VAC RMS 32 mH @ 208 VAC RMS 25.2 mH @ 208 VAC RMS 13 mH @ 208 VAC RMS 22 mH @ 380 VAC RMS
Rated Voltage/Current (0.85 power factor) 110 VAC 1ø rms @ 60 Hz/2.0 A rms 110 VAC 1ø rms @ 60 Hz/4.0 A rms 208 VAC 1ø rms @ 60 Hz/8 A rms 208 VAC 1ø rms @ 60 Hz/15 A rms 208 VAC 1ø rms @ 60 Hz/18 A rms 208 VAC 1ø rms @ 60 Hz/30 A rms 380 VAC 1ø rms @ 60 Hz/40 A rms
Stroke Limit (centered within 1 mm) 12 mm 14 mm 18 mm 24 mm 24 mm 30 mm 36 mm
Nominal BL Product at Maximum Voltage 47.7 N/Ampere 43.3 N/Ampere 65.4 N/Ampere 52.1 N/Ampere 52.7 N/Ampere 45.2 N/Ampere 62 N/Ampere
Intrinsic Stiffness (approximate) 31 kN/m 41 kN/m 56 kN/m 97 kN/m 123.4 kN/m 160 kN/m 190 kN/m
Damping, Rm 5.0 N-s/m 7.0 N-s/m  17 N-s/m  20 N-s/m  23.7 N-s/m  55 N-s/m  103 N-s/m 
Total Mass 1.896 kg  (including piston & shaft) 2.86 kg (including piston & shaft) 6.217 kg (including piston & shaft) 11.41 kg (including shaft) 12.66 kg  28.8kg with shaft and 8.79" piston  54.54 kg with shaft and 9.7" piston
Moving Mass 0.49 kg (with 1.15” piston) 0.715 kg (with 1.902” piston) 2.8 kg (with 2.554” piston) 2.5 kg (motor only),  3.6 kg with 3.66" piston 4.139 kg with 4.25" piston 6.0 kg (motor only) 12.5 kg (motor only)
Outside Diameter 102 mm  132 mm 175 mm 226 mm 241 mm  297 mm 362 mm
Specifications

Additional Information

Features

The RIX Industries system provides no maintenance, linear reciprocating motors and alternators with oil-free flexure bearings that have virtually unlimited life. 

SYSTEM SPECIFICATIONS:

Motor Model 1s102M 1s132M 1s175M 1s226M 1s241M 1s297M 1s362M
               
Nominal Input Power Rating 120 W at 60 Hz, 10 mm stroke 275 W at 60 Hz, 12 mm stroke 750 W at 60 Hz, 16 mm stroke 1,400 W at 60 Hz, 20 mm stroke 2,000  W at 60 Hz, 20 mm stroke 5,000 W at 60 Hz, 26 mm stroke 10,000  W at 60 Hz, 32 mm stroke
Rated Acoustic Output (@ 60 Hz) Acoustic power as driver – 90 W Acoustic power as driver – 220 W  Acoustic power as driver – 550 W Acoustic power as driver – 1000 W Acoustic power as driver – 1,600W  Acoustic power as driver – 3800W Acoustic power as driver – 7500W
Stator Resistance 7 ohm 2.2 ohm 1.8 ohm 0.9 ohm 0.9 ohm @ 60Hz AC 0.2 ohm 0.22 ohm
Stator Inductance 84 mH @110 VAC RMS 46 mH @ 110 VAC RMS 62 mH  @ 208 VAC RMS 32 mH @ 208 VAC RMS 25.2 mH @ 208 VAC RMS 13 mH @ 208 VAC RMS 22 mH @ 380 VAC RMS
Rated Voltage/Current (0.85 power factor) 110 VAC 1ø rms @ 60 Hz/2.0 A rms 110 VAC 1ø rms @ 60 Hz/4.0 A rms 208 VAC 1ø rms @ 60 Hz/8 A rms 208 VAC 1ø rms @ 60 Hz/15 A rms 208 VAC 1ø rms @ 60 Hz/18 A rms 208 VAC 1ø rms @ 60 Hz/30 A rms 380 VAC 1ø rms @ 60 Hz/40 A rms
Stroke Limit (centered within 1 mm) 12 mm 14 mm 18 mm 24 mm 24 mm 30 mm 36 mm
Nominal BL Product at Maximum Voltage 47.7 N/Ampere 43.3 N/Ampere 65.4 N/Ampere 52.1 N/Ampere 52.7 N/Ampere 45.2 N/Ampere 62 N/Ampere
Intrinsic Stiffness (approximate) 31 kN/m 41 kN/m 56 kN/m 97 kN/m 123.4 kN/m 160 kN/m 190 kN/m
Damping, Rm 5.0 N-s/m 7.0 N-s/m  17 N-s/m  20 N-s/m  23.7 N-s/m  55 N-s/m  103 N-s/m 
Total Mass 1.896 kg  (including piston & shaft) 2.86 kg (including piston & shaft) 6.217 kg (including piston & shaft) 11.41 kg (including shaft) 12.66 kg  28.8kg with shaft and 8.79" piston  54.54 kg with shaft and 9.7" piston
Moving Mass 0.49 kg (with 1.15” piston) 0.715 kg (with 1.902” piston) 2.8 kg (with 2.554” piston) 2.5 kg (motor only),  3.6 kg with 3.66" piston 4.139 kg with 4.25" piston 6.0 kg (motor only) 12.5 kg (motor only)
Outside Diameter 102 mm  132 mm 175 mm 226 mm 241 mm  297 mm 362 mm
Downloads